/* Munich, Germany COMPANY CONFIDENTIAL All Rights Reserved .AUTHOR U. Schmitt, ICM MP PO8 MCH53 .PROJECT WINSWUP .SHORT_DESCR Interface to the lowlayer-DLL .SW_COMPONENT .SW_TYPE .VERSION 1.3 please increase the two defines !!! .DATE 2004-09-01 .EXIT_CODES .STATUS FIRST_TRY .CHANGE_CONTROL Version | Date | Changed by | Reason for Change --------+----------+------------+---------------------------------------------- 0.1 |2002-09-02| D.Dittmer | file created, content drawn from err_text.h --------+----------+------------+---------------------------------------------- 0.2 |2002-10-28| L.Sillge | entry en_SIG_SW_REJECTED added --------+----------+------------+---------------------------------------------- 0.3 |2003-01-29| L.Sillge | entry en_SIG_SW_CORRUPT added --------+----------+------------+---------------------------------------------- 0.4 |2003-09-18| H.G.Weyers | entry en_BOOTCORE_NOT_ACKNOWLEDGE --------+----------+------------+---------------------------------------------- 0.5 |2003-09-26| H.G.Weyers | entry en_ERR_ADDITIONAL_MAP_INFO --------+----------+------------+---------------------------------------------- 0.6 |2003-10-27| H.G.Weyers | entry en_PROJECT_NOT_SET | | | en_PROJECT_NOT_SUPPORTED | | | en_ADDMAPINFO_WRONG_SIZE | | | en_ADDMAPINFO_BUFFER_OVERWRITE | | | en_ADDMAPINFO_LEN_NOT_SET | | | en_LENCHECK_ILLEGAL_COMMAND | | | en_LENCHECK_BUFFER_OVERRUN | | | en_LENCHECK_CHECKSUM_INVALID | | | en_LENCHECK_ADDRESS_CHECKSUM_INVALID | | | en_LENCHECK_INVALID_STATE | | | en_LENCHECK | | | en_WRONG_BLOCK_OR_ADDRESS |2003-11-10| H.G.Weyers | entry en_NO_32BIT_FILE | | | en_OLD_STRINGIDENTIFICATION --------+----------+------------+---------------------------------------------- 0.7 |2003-12-08| H.G.Weyers | modified parameter from en_BYTE_PROG (%02X%02X%02X%02X) to show 32-Bit address --------+----------+------------+---------------------------------------------- 0.8 |2004-01-29| J. Garrido | Change any reference to BFB to BFC | | | Chage en_ONLY_EGOLD to en_ONLY_SGOLDLITE --------+----------+------------+---------------------------------------------- 0.9 |2004-03-08| J. Garrido | New string for en_BOOTCORE_NOT_ACKNOWLEDGE | | | Neww error en_SIG_NOT_FREEZED --------+----------+------------+---------------------------------------------- 1.0 |2004-03-08| J. Garrido | New error: | | | en_BC_INTERFACE_NOT_OK | | | en_DEVCON_NOT_OK | | | en_CHARGER_PRESENT | | | en_BC_HW_INTERFACE_NOT_SUPPORTED | | | en_BC_BAUDRATE_NOT_SUPPORTED | | | en_MEM_ERROR --------+----------+------------+---------------------------------------------- 1.01 |2004-05-26| J. Garrido | en_DEFAULT_CMD_BLOCKS is now used.Just comment removed --------+----------+------------+---------------------------------------------- 1.02 |2004-08-26| J. Garrido | change text for en_DEVCON_NOT_OK --------+----------+------------+---------------------------------------------- 1.03 |2004-09-01| J. Garrido | Correction on text for en_CHARGER_PRESENT --------+----------+------------+---------------------------------------------- .STILL_TODO */ /* INDENT: -nbr -nce -ei -ip -lp -pro -sc -c:33 -cci:3 -cd:33 -ci:3 -cli:3 -cp:0 -d:0 -di:0 -i:3 -l:78 -lc:78 -tabs:3 -tabu */ /*********************************************************************************************************/ #define ERR_TEXT_VERS_MAJOR 1 #define ERR_TEXT_VERS_MINOR 03 #define ERR_TEXT_DEVELOPER "Garrido" #include #include "werrenum.h" #include "err_text.h" t_enumErrorDescription ErrorDescription[] = { // wseril1.c { en_ALREADY_OPEN , en_ALTER_CONNECT , "ComPort is alrady open"}, { en_CREATE_FILE , en_ALTER_CONNECT , "ComOpen : error on CreateFile"}, { en_SET_COMMSTATE , en_ALTER_TRANSMISSION , "Error on Changing Com-State"}, { en_NOT_OPEN , en_ALTER_CONNECT , "ComPort is not open"}, { en_TIMEOUT , en_ALTER_CONNECT , "Error on Changing Timeout"}, { en_GET_BAUD , en_ALTER_CONNECT , "Error on getting baudrate"}, { en_BAUDRATE , en_ALTER_CONNECT , "Error on configuring, false baudrate"}, { en_WRITE_FILE , en_ALTER_CONNECT , "Error on WriteFile"}, { en_READ_FILE , en_ALTER_CONNECT , "Error on ReadFile"}, { en_INVALID_HANDLE_VALUE , en_ALTER_CONNECT , "Invalid Handle for Com-Port"}, // wseril2.c { en_NO_VERSION , 0 , "No version number of Serial Low-DLL available"}, { en_DEFAULT_CMD_BLOCKS , en_ALTER_TRANSMISSION , "Error in HandleDefaultCmdBlocks"}, { en_WAIT_ON_CMD_BLOCK , en_ALTER_TRANSMISSION , "Error on waiting for CMD-Block"}, { en_MAX_BIN_LEN_REACHED , en_ALTER_TRANSMISSION , "Maximum Bin-length reached"}, { en_UNKNOWN_BYTE , en_ALTER_TRANSMISSION , "Unknown Byte %02X received"}, { en_REC_TIMEOUT , en_ALTER_TRANSMISSION , "Receive-Timeout, nothing received"}, { en_UNKNOWN_CHAR , en_ALTER_TRANSMISSION , "Unknown character received, now flushing inbuf"}, { en_UNKNOWN_REC_VALUE , en_ALTER_TRANSMISSION , "Unknown retval %d from ReceiveValue Value received = %02Xh"}, { en_COMM_ERROR , en_ALTER_TRANSMISSION , "Aborting due to transmission-error"}, { en_CHECK_SUM_ERROR , en_ALTER_TRANSMISSION , "Check sum error"}, { en_CMD_REC , en_ALTER_TRANSMISSION , "Unexpected Cmd-Block received"}, { en_SERIAL_ERROR , en_ALTER_TRANSMISSION , "Error on serial interface"}, { en_READ_CMD , en_ALTER_TRANSMISSION , "Error on read CMD-Block"}, // not used { en_WAIT_FF , en_ALTER_TRANSMISSION , "Timeout on waiting for FF"}, // wseril3.c { en_NO_READY_FLASH_ERASE , en_ALTER_TRANSMISSION , "Error on waiting for FlashBlock-EraseReady"}, { en_SEND_FLASH_ERASE , en_ALTER_TRANSMISSION , "Error on sending Erase-Flash-Block-CMD"}, { en_ERASE_AREA_NOT_OK , en_ALTER_SW_VERSION , "Wrong Erase-Address, not possible from %lXh to %lXh"}, { en_MALLOC_REQUEST_FLASH_BLOCKS , 0 , "No memory on malloc for Flash-Areas"}, { en_FLASHBLOCK_SIZE_DEFAULT , en_ALTER_TRANSMISSION , "Unknown Answer from Mobile on request for Erase-Area"}, { en_TIMEOUT_REQUEST_FLASH_BLOCKS , en_ALTER_TRANSMISSION , "Timeout-Error waiting for Test-Area-ACK"}, // wmob_err.c { en_RAM_FF , en_ALTER_MOBILE_DEFECT , "Error on RAM-Test with FF"}, { en_RAM_PATTERN , en_ALTER_MOBILE_DEFECT , "Error on RAM-Test with pattern"}, { en_RAM_00 , en_ALTER_MOBILE_DEFECT , "Error on RAM-Test with 00"}, { en_RAM_UNKNOWN , en_ALTER_MOBILE_DEFECT , "Unknown Error on RAM-Test"}, { en_VOLTAGE_RANGE , 0 , "Erase-Error Block %d : Vpp voltage range"}, { en_CMD_SEQUENCE , 0 , "Erase-Error Block %d : Error in the command sequence"}, { en_ERASE_NOT_POSSIBLE , 0 , "Erase-Error Block %d : Erase not possible"}, { en_NO_BLOCK , 0 , "Erase-Error Block %d : Block does not exist"}, { en_BYTE_PROG , 0 , "Byte-Program-Error Nr: %d on adress %02X%02X%02X%02X"}, { en_FINAL_CHECK , 0 , "Check-sum-error final test"}, { en_UNKNOWN_FLASH , 0, "Unknown flash"}, { en_NOT_SUPPORTED , 0 , "Function not supported until now in Mobile"}, { en_PROJECT_NOT_SET , 0 , "Project id was not send, so no flash configuration was set and no memory is available"},/* new!*/ { en_PROJECT_NOT_SUPPORTED, 0 , "No flash mapping and constants available in uploadsw for the requested project id"}, /* new!*/ { en_ADDMAPINFO_WRONG_SIZE, 0 , "The internal structure length fit not to requested mapinfo length"}, /* new!*/ { en_ADDMAPINFO_BUFFER_OVERWRITE, 0 , "The size of transfered additional map info fits not to previous send length"}, /* new!*/ { en_ADDMAPINFO_LEN_NOT_SET, 0 , "No len info was send before additional map info was send"}, /* new!*/ { en_LENCHECK_ILLEGAL_COMMAND, 0 , "The lencheck file format contains wrong data (illegal command)"}, /* new!*/ { en_LENCHECK_BUFFER_OVERRUN, 0 , "The lencheck file format contains wrong data (buffer overrun)"}, /* new!*/ { en_LENCHECK_CHECKSUM_INVALID, 0 , "The lencheck file format contains wrong data (checksum invalid)"}, /* new!*/ { en_LENCHECK_ADDRESS_CHECKSUM_INVALID, 0 , "The lencheck file format contains wrong data (address checksum invalid)"}, /* new!*/ { en_LENCHECK_INVALID_STATE, 0 , "The lencheck file format contains wrong data (invalid state)"}, /* new!*/ { en_LENCHECK, 0 , "The lencheck file format contains wrong data"}, /* new!*/ { en_WRONG_BLOCK_OR_ADDRESS, 0 , "Block number or an address is not in flash space"}, /* new!*/ { en_UNABLE_TO_WRITE_STATISTIC, 0 , "Unable to write statistic"}, /* new!*/ { en_UNKNOWN_ERROR , 0 , "Unknown Mobile-Error: %02X"}, // wbfbtool.c { en_BFC_NO_CALLBACK , 0 , "No CallBackFunctions for BFC-Lib installed"}, { en_BFC_COMM_NOT_OPEN , 0 , "Could not open Comport for BFC-Lib, maybe Comport is in use"}, { en_BFC_MOBILE_NO_SWITCHON,0 , "Could not switch on Mobile"}, { en_BFC_MOBILE_NO_PING , en_ALTER_CONNECT , "Could not Ping Mobile"}, { en_THIS_FILE_NO_NEW_UPDATE , 0 , "This file can\'t be updated with new concept"}, { en_BFC_NO_NEW_UPDATE , 0 , "No answer from Mobile, maybe not with new Update-Concept ?"}, { en_BFC_READY_FALSE , 0 , "BFC : ready and false"}, // not used { en_CUSTOMER_REBOOT , 0 , "Error on requesting customer reboot"}, // not used { en_PUT_COUNT , 0 , "Error on requesting put count"}, // not used { en_BC_INTERFACE_NOT_OK, 0 , "Wrong bootcore interface version"}, { en_DEVCON_NOT_OK, en_ALTER_CONNECT, "Update not supported with plugged cable"}, { en_CHARGER_PRESENT, 0, "Simultaneous updating and charging could be dangerous, please remove charger and try again"}, { en_BC_HW_INTERFACE_NOT_SUPPORTED, en_ALTER_CONNECT, "Update not allow with this device"}, { en_BC_BAUDRATE_NOT_SUPPORTED, en_ALTER_CONNECT, "Baudrate not supported"}, { en_MEM_ERROR, en_ALTER_SW, "Out of Memory"}, // swupwork.c { en_NO_DATE_TIME , en_ALTER_SW_VERSION , "No Date/Time-Info available, impossible to DIFF-Swup"}, { en_WRONG_DATE_TIME , en_ALTER_SW_VERSION , "Wrong Date/Time for DIFF-SWUP ! XDI must fit exactly to SW in Mobile"}, { en_NO_REQUEST , en_ALTER_TRANSMISSION , "No Request for Update-SW after Bootstraploader"}, { en_ERR_SEND_UPDATE , 0 , "Error on requesting update-sw"}, { en_CANT_OPEN , en_ALTER_TRANSMISSION , "Opening Comport %d with Speed %d Baud not possible"}, { en_ERR_WAIT_FLASH_CODE , en_ALTER_TRANSMISSION , "Error on waiting for Flash-Code"}, { en_UNKNOWN_FLASH_CODE , 0 , "Unknown Flashcode %02X%02X"}, { en_WAIT_FLASH_SIZE , en_ALTER_TRANSMISSION , "Error on Requesting Flash-Size"}, { en_WRONG_FLASH_SIZE , en_ALTER_SW_VERSION , "Error : you are trying to update a SW for %ld Bytes into a Mobile with only space for %ld Bytes !"}, { en_NO_UPDATE , en_ALTER_SW_VERSION , "Error : Update of %s SW not possible into a %s !"}, { en_INCOMPATIBLE , en_ALTER_SW_VERSION , "Error : SW-Date and Version are incompatible, Mobile : %s Date : %s <=> File : %s Date : %s !"}, { en_INCOMPATIBLE_VERS , en_ALTER_SW_VERSION , "Error : SW-Version is incompatible, Mobile: %s <=> File: %s !"}, { en_WAIT_SPLIT_ID_ANSWER , 0 , "Error on waiting for Split-ID-Answer"}, { en_WRONG_SPLIT_ID , 0 , "Wrong Split-ID, SW and LanguageGroup dont fit together"}, { en_MALLOC_ERROR , 0 , "Malloc error"}, // not used { en_ENABLE_FLASHBLOCK , 0 , "Error on enabling flash block"}, { en_WAIT_COMPRESS_ANSWER , 0 , "Error on waiting for Compression-Answer"}, { en_WAIT_LANGINFO_ANSWER , 0 , "Error on waiting for LanguageGroup-Answer"}, { en_WAIT_CALC_SPLIT_INFO_ANSWER , 0 , "Error on waiting for Splitinfo answer"}, { en_WAIT_STAT_DATA , 0 , "Error on waiting for Stat-Data"}, { en_SW_PROJECT , 0 , "No Update-SW found for Project : %s SVN %2X %s SynchStation"}, { en_UNABLE_WRITE_BGJ, 0 , "Unable to write BGJ"}, { en_CANT_CONNECT , en_ALTER_CONNECT , "Cant connect to Mobile with BootstrapLoader on Com %d"}, { en_INCOMPATIBLE_VERSION , 0 , "Library and Executable have different Interface-Versions !"}, { en_MUTEX , 0 , "Error opening Mutex. Update Nr: %d"}, { en_COMPRESS_NOT_SUPPORTED, 0, "Error : Compression/ Algorithm not supported"}, { en_MOBILE_SW_TRANS , en_ALTER_TRANSMISSION , "Error on Transmission"}, { en_WAIT_ACK_EOT , en_ALTER_TRANSMISSION , "Error on waiting for Ack EOT"}, { en_WAIT_SW_VERSION , en_ALTER_TRANSMISSION , "Error on waiting for SW-Version"}, { en_ERR_ADDITIONAL_MAP_INFO , en_ALTER_TRANSMISSION , "Error: AdditionalMapInfo on Comport %d \n"}, // dyna_dll.c { en_SCAN_PROJECTS , 0 , "Error on ScanDirectoryForAvailableProjects"}, { en_DLL_OUT_OF_DATE , en_ALTER_SW_VERSION , "DLL is out of date, get a new package !"}, { en_LOAD_FAILED , 0 , "Load failed : %s"}, // hehawrap.c / fihawrap.c { en_LIB_EXE_DIFF , 0 , "Library and Executable have different Interface-Versions, Executable must be compiled new !"}, { en_FILE_READ , en_ALTER_FILE_ERROR , "Alread a file read ! Please release first !"}, { en_INIT_READ , en_ALTER_FILE_ERROR , "Error occured Initialization for READ : %d"}, { en_CHK_SUM , en_ALTER_FILE_ERROR , "ChecksummError in HEADER of XBI-File"}, { en_HEAP_NOT_INI , en_ALTER_FILE_ERROR , "HeapLib not initialized !"}, { en_HEAP_LEN , en_ALTER_FILE_ERROR , "Data len in heap zero, HeapLib initialized ?"}, { en_STRANGE_ERROR , en_ALTER_FILE_ERROR , "Strange Error :-)) Number %d !"}, { en_ONLY_SGOLDLITE , en_ALTER_FILE_ERROR , "Currently only SGOLDLite-Projects supported !"}, { en_NO_SW , en_ALTER_FILE_ERROR , "No Update-SW found !"}, { en_READ_XBI , en_ALTER_FILE_ERROR , "Some Error : %d occured on reading XBI-Data"}, { en_OUTDATED , en_ALTER_FILE_ERROR , "Your version of WINSWUP/LIBRARY is outdated ! Software-Update not possible ! Get a new version !"}, { en_OPEN_FILE , en_ALTER_FILE_ERROR , "Can't open file %s"}, { en_XBI_LEN , en_ALTER_FILE_ERROR , "XBI-Length 0 !"}, { en_NO_SIEMENS , en_ALTER_MOBILE , "Not a Siemens-Mobile-Phones-File"}, { en_FILE_SIZE , en_ALTER_FILE_ERROR , "Error occured during FileSize-Detection : %d"}, { en_CANT_ALLOC , en_ALTER_FILE_ALLOC_ERROR , "Could not allocate %lu Bytes for XBI-File"}, // heaphand.c / filehand.c { en_CANT_ADD , en_ALTER_FILE_ERROR , "Can't add element for erase info!"}, { en_CANT_COPY , en_ALTER_FILE_ERROR , "Could not copy element to list!"}, { en_CANT_MALLOC , en_ALTER_FILE_ERROR , "Can't malloc heap for add. map info!"}, { en_MORE_INFO , en_ALTER_FILE_ERROR , "More map info in xbi header than expected!"}, { en_LOCATER_ENTRY , en_ALTER_FILE_ALLOC_ERROR , "Error mallocing heap for locater entry!"}, { en_SPLIT_INSERT , en_ALTER_FILE_ALLOC_ERROR , "SplitElementInsert returns error!"}, { en_HEAP_CORRUPT , en_ALTER_FILE_ERROR , "Heap data corrupt at location %d"}, { en_MEM_ALLOC , en_ALTER_FILE_ERROR , "Heapchk: no memory allocated!"}, { en_HEAP_INCON , en_ALTER_FILE_ERROR , "Heapchk: detected inconsistency!"}, { en_FSEEK , en_ALTER_FILE_ERROR , "Error on data access"}, { en_FREAD , en_ALTER_FILE_ERROR , "Read error in file %s!"}, { en_DESTROYED , en_ALTER_FILE_ERROR , "Data file destroyed at %lu"}, { en_STAT_FILE , en_ALTER_FILE_ERROR , "Error on file access"}, { en_READ_KENNUNG , en_ALTER_FILE_ERROR , "ReadKennung returned: %d"}, { en_COUNT_BYTES , en_ALTER_FILE_ERROR , "Error: CountXbiHeaderBytes returnes %d"}, { en_NO_READ_ACCESS , en_ALTER_FILE_ERROR , "No read access to file %s"}, { en_FIND_FILE , en_ALTER_FILE_ERROR , "Can't find file %s"}, { en_DATA_ACCESS , en_ALTER_FILE_ERROR , "Error on data access"}, { en_NO_32BIT_FILE, en_ALTER_FILE_ERROR , "Error file: Error on reading XBI-header"}, { en_OLD_STRINGIDENTIFICATION, en_ALTER_FILE_ERROR , "Error old 24-Bit file: Please select a 32-Bit file for SGOLD"}, // swup_eg.c { en_OPEN_COMPORT , en_ALTER_CONNECT , "Opening Comport %d with Speed %d Baud not possible"}, { en_REC_BLOCK1 , en_ALTER_TRANSMISSION , "Nothing received after BOT-Block1"}, { en_WRONG_BLOCK1 , en_ALTER_TRANSMISSION , "Wrong Char %02X received after BOT-Block1"}, { en_REC_BLOCK2 , en_ALTER_TRANSMISSION , "Nothing received after BOT-Block2, perhaps device protected"}, { en_WRONG_BLOCK2 , en_ALTER_TRANSMISSION , "Wrong Char %02X received after BOT-Block2"}, { en_REC_BLOCK3 , en_ALTER_TRANSMISSION , "Nothing received after BOT-Block3"}, { en_WRONG_BLOCK3 , en_ALTER_TRANSMISSION , "Wrong Char %02X received after BOT-Block3"}, { en_REC_BLOCK4 , en_ALTER_TRANSMISSION , "Nothing received after BOT-Block4"}, { en_WRONG_BLOCK4 , en_ALTER_TRANSMISSION , "Wrong Char %02X received after BOT-Block4"}, { en_REC_BAUD_BLOCK , en_ALTER_TRANSMISSION , "Nothing received after Baud-BOT-Block"}, { en_WRONG_BAUD_BLOCK , en_ALTER_TRANSMISSION , "Wrong Char %02X received after Baud-BOT-Block"}, { en_CHANGE_SPEED , en_ALTER_TRANSMISSION , "Changing Speed on Comport %d to %d Baud not possible, possible errors: wrong Baudrate / not installed driver/ wrong serialcard ?"}, { en_REC_PING , en_ALTER_TRANSMISSION , "Nothing received after Baud-Ping"}, { en_WRONG_PING , en_ALTER_TRANSMISSION , "Wrong char %02X received after Baud-Ping"}, { en_REC_FALLBACK , en_ALTER_TRANSMISSION , "Nothing received after fallback to 57kBaud"}, { en_WRONG_FALLBACK , en_ALTER_TRANSMISSION , "Wrong char %02X after fallback to 57kBaud"}, { en_REC_SYNC_BYTE , en_ALTER_TRANSMISSION , "Nothing received after synch-byte"}, { en_WRONG_SYNC_BYTE , en_ALTER_TRANSMISSION , "Wrong char %02X after synch-byte"}, { en_REC_BLOCK5K , en_ALTER_TRANSMISSION , "Nothing received after BOT-Block 5k"}, { en_WRONG_BLOCK5K , en_ALTER_TRANSMISSION , "Wrong char %02X after BOT-Block 5k"}, { en_ALTER_CONNECT , 0 , "Cant connect mobile !\nCheck if attached correctly or switch baudrate or comport"}, { en_ALTER_TRANSMISSION , 0 , "Cant connect mobile !\nCheck if attached correctly"}, { en_ALTER_SW_VERSION , 0 , "Update not possible !\nWrong SW-version"}, { en_ALTER_MOBILE , 0 , "Update not possible !\nWrong mobile"}, { en_ALTER_SW , 0 , "Update not possible !\nSW defect"}, { en_ALTER_MOBILE_DEFECT , 0 , "Mobile defect"}, { en_ALTER_FILE_ERROR, 0 , "Error on reading new Mobile-SW" }, { en_ALTER_FILE_ALLOC_ERROR, 0 , "Error on reading new Mobile-SW, not enough memory" }, { en_BOOTCORE_MASK, 0 , "No Bootcore detected"}, { en_BOOTCORE_BAUDRATE, 0 , "Bootcore does't support selected baudrate"}, { en_BOOTCORE_NOT_ACKNOWLEDGE, 0 , "Device protected. Only secure update allowed"}, { en_SIG_WRONGHASH , 0 , "Mobile requested signature, but software doesn't support it"}, { en_SIG_NOSIGNATURE, 0 , "Mobile requested signature, but signature data are not available"}, { en_SIG_NOT_FREEZED, 0 , "Secured update not possible, device not prepared."}, { en_SIG_SIGNREJECT, 0 , "Software signature was rejected"}, { en_SIG_GENERAL, 0 , "Software signature negotiation failure (%02X)"}, { en_SIG_SW_REJECTED, 0 , "Software update denied by mobile"}, { en_SIG_SW_CORRUPT, 0 , "Update aborted, corrupt software was reported by mobile"}, { en_OVERFLOW , 0 , "Overflow on error list"} }; size_t ErrorDescriptionSize = sizeof (ErrorDescription); size_t t_enumErrorDescriptionSize = sizeof (t_enumErrorDescription);